Guangdong Yonglong Aluminum Co., Ltd.
Unity and Enterprising, Innovation Development, Quality Oriented, Service Win！ Welcome customers from all over the world！
Add to Cart
Wood finish aluminum extrusion profile , bedroom wardrobe sliding door profile
Specifiaction:
| Description | Wood finish aluminum extrusion profile , bedroom wardrobe sliding door profile |
| Material Thickness(t) | t=1.0 / 1.2 / 1.4 |
| Material | Aluminum Alloy 6063, 6061 |
| Annealing Treatment | T5,T6 |
| Color | Green, Grey, Black, White, (RAL series)etc. |
| Surface Treatment |
Mill finish, anodized, powder coated, electrophoresis, sand balsting etc.and depend on customer’s demand.
|
| Shape | Square, Round, Flat, Oval, and according to customer's drawing. |
| Length | Normal length=6m or in customer's order |
| Usage |
Building, Production Line, Decoration, Industrial, Transportation, Door and window, etc.
|
| Package | 1. Pearl cotton foam for each profile; 2. Wrap with shrink film exterior; 3. Packed according to customer request. |
| Advantages/Features | Providing colorful products with various mechanical performances to adapt all kinds of architectural styles |
Operation procedure of hot-transfer wood printing process
1: The preparation for production
According to production plan sheet ready already spray or electrophoresis good base material and the color of the need to transfer wood grain paper, according to the size of the profile section will open good required length wood grain paper, the general scale Zhou Changkuan 3 ~ 5 cm width than the cross section
2: the paper bag
1: The length of the section is 1-2cm, and the paper is laid out.
2: use wood grain paper to wrap the base material that is reprinted, the interface that USES high temperature glue paper to hold the paper, in case the paper loosen. (note: on the front of the reprinted paper, the paper is reprinted on the front of the reprinted substrate. No wrinkles, no cracks, etc.
3: sets of plastic bags
1: will be the base material of wood grain thermal transfer paper wrapped over stay high temperature resistance and good sealing tube plastic bag, by adopting appropriate profile cross section sizes of high-temperature tubular plastic bag.
2: Note that the plastic glue bag at the end of the bag is reserved for the length of the plastic bag, which is usually reserved for 15cm in the vacuum end, and 22-25cm on the other side for sealing.
3: When operating, be careful to lightly put, avoid the glue bag to cut the hole, if there is this image must be repaired.
4: vacuum
1: put one end of the bag on the vacuum valve, find the valve, slowly vacuum, until the plastic bag can be fully and effectively glued to the substrate. The negative pressure size of the vacuum should be adjusted according to the characteristics of the reprinted substrate and the negative pressure of the plastic bag.
2: Arrange the plastic bag flat and open all the vacuum valves.
3: Open the door of the fire door to transfer.
5: Bake the transfer
1: the length of the baking transfer printing temperature and time should be according to the characteristics of the transfer printing substrate, to transfer the texture depth and comprehensive factors such as specific performance of oven do appropriate adjustments, usually transfer printing temperature is 160 ~ 190 ℃, time of 10 ~ 20 minutes.
2: During the baking process of the workpiece, observe the temperature change and ensure the furnace temperature is stable.
3: Check the furnace temperature regularly once a month to understand the change of the furnace temperature, so as to set up the best furnace temperature, so as to better make the base material bake transfer.
6: tear open plastic bags
From the heat transfer in the furnace has been transfer printing substrate, from one end of the transfer printing substrate was able to solve the plastic bag, on the other side find some plastic bag and put away (note: the plastic bag can protect the reuse) should be paid attention to.
7: tear open paper
Remove the wood grain paper from the printed section. Open one end and draw the paper from the other end, and then you can use two or three to increase the speed of the paper.
8: Quality inspection
The surface quality, color and appearance of the finished paper will be inspected, the workpiece of quality defects will be selected, and it will be processed in the pending area.
9: packaging
The products inspected and qualified shall be packed in accordance with the requirements or plans of the contract.
